[Date Prev][Date Next][Thread Prev][Thread Next][Minivend by date
][Minivend by thread
]
RE: [mv] [mv 4.02] - make test fails
****** message to minivend-users from Ed LaFrance <edlafrance@printexusa.com> ******
Chris -
Thanks for the heads up. If you posted the fix, I guess I did not see it
or find it in the archives. Could you post it again? I will make the same
changes in my copy and try to complete the install.
Thanks,
Ed L.
At 10:42 PM 3/22/00 -0800, you wrote:
>****** message to minivend-users from "Christopher Thompson"
><ct@arborinternet.com> ******
>
>I had the same experience on FreeBSD, with the:
>
>link/inetmode.........not ok 5
>server/control........not ok 6
>
>I went ahead and installed (after manually fixing the Makefile). The
>server starts up and serves pages fine. I noticed that the check script
>does not work. It hangs (with -o) and eventually seems to time-out with a
>link error. Probably the same error as reported by test. I have not
>installed Minimate, but assume it might have problems as well.
>
>I reported on the list before that the install script does not handle
>virtual server environments where all the paths should be relative the
>/usr/home/myname (including Perl and Apache). It is not clear to me
>whether the link errors are from the install being bad or the virtual
>server environment.
>
>
> > -----Original Message-----
> > From: owner-minivend-users@minivend.com
> > [mailto:owner-minivend-users@minivend.com]On Behalf Of Ed LaFrance
> > Sent: Wednesday, March 22, 2000 5:33 PM
> > To: minivend-users@minivend.com
> > Subject: [mv] [mv 4.02] - make test fails
> >
> >
> > ****** message to minivend-users from Ed LaFrance
> > <newmedia@newmediaems.com> ******
> >
> > Hello all -
> >
> > I have seen references to this problem in general in the
> > archives, but the
> > solutions, when they are there, vary widely, so I though I
> > would send it
> > out to the list.
> >
> > I am trying to install minivend 4.02 on an ISP'S server, which
> > is running
> > BSDI BSD/OS 4.0.1. Perl 5.00503. Things work until I get to
> > make test -
> > below is a snippet of terminal output:
> > ------------
> >
> > www-pws7: {14} % make test && make install
> > PERL_DL_NONLAZY=1 /usr/bin/perl -Iblib/arch -Iblib/lib
> > -I/usr/libdata/perl5/5.00503/i386-bsdos -I/us
> > r/libdata/perl5/5.00503 test.pl
> > server/unixmode.......ok 1
> > server/startup........ok 2
> > link/unixmode.........ok 3
> > server/inetmode.......ok 4
> > link/inetmode.........not ok 5
> > server/control........not ok 6
> > 6 tests run -- 2/6 failed.
> > *** Error code 1
> >
> > Stop.
> > ------------
> >
> > The process stops right there. I have not tried to run "make install"
> > without "make test"; I don't expect that it would work too
> > well. I don't
> > profess to be much of a sysadmin. Anyone have any suggestions
> > as to where
> > I should start?
> >
> > Thanks in advance for any help that is offered.
> >
> > - Ed L.
> >
> > -
> > To unsubscribe from the list, DO NOT REPLY to this message.
> > Instead, send
> > email with 'UNSUBSCRIBE minivend-users' in the body to
> > Majordomo@minivend.com.
> > Archive of past messages: http://www.minivend.com/minivend/minivend-list
> >
>
>-
>To unsubscribe from the list, DO NOT REPLY to this message. Instead, send
>email with 'UNSUBSCRIBE minivend-users' in the body to Majordomo@minivend.com.
>Archive of past messages: http://www.minivend.com/minivend/minivend-list
Printex Marking Technologies
12113 Kirkham Rd.
Poway, CA 92064 U.S.A.
858-513-2418
800-982-1928
858-513-2419 FAX
http://www.printexusa.com
-
To unsubscribe from the list, DO NOT REPLY to this message. Instead, send
email with 'UNSUBSCRIBE minivend-users' in the body to Majordomo@minivend.com.
Archive of past messages: http://www.minivend.com/minivend/minivend-list