Akopia Akopia Services

[Date Prev][Date Next][Thread Prev][Thread Next][Minivend by date ][Minivend by thread ]

Re: [mv] Still struggling with mv4 installation.



******    message to minivend-users from Ed LaFrance <newmedia@newmediaems.com>     ******

At 12:54 AM 3/24/00 -0500, you wrote:
>******    message to minivend-users from Mark Stosberg 
><mark@summersault.com>     ******
>
>
> > Writing /home/v/visprox/mvend/auto/MiniVend/.packlist
> > ## Differing version of ./perllocal.pod found. You might like to
> > rm /usr/libdata/perl5/5.00503/i386-bsdos/perllocal.pod
> > ## Running 'make install UNINST=1' will unlink this file for you.
> > Appending installation info to /home/v/visprox/mvend/perllocal.pod
>
>Ed,
>
>  I got the above message too when installing on FreeBSD 3.1. I ignored
>it and proceeded without problem, so I don't think that's your problem.

Mark -

When I got the message you see, the install process stopped right 
there.  Normally it configures the server and starts it; that did not 
happen.  Did the same thing happen to you?  If so, what did you do?  I do 
not have access permissions to do anything to the files in the ISP's Perl 
install, so I could not run 'make install UNINST-1' successfully.
What I ended up doing is renaming minivend.cfg.dist to minivend.cfg and 
trying to start the server manually.  I indicates that it is started, but 
apparently is it is not - it does no show up as a running process:

www-pws7: {3} % mvend/bin/minivend -start
Low traffic settings.
MiniMate is NOT active.
MiniVend V4.02
MiniVend server started in INET and UNIX mode(s) (process id 4299)
Continuing in UNIX MODE ONLY
www-pws7: {4} % ps
   PID  TT  STAT      TIME COMMAND
  4285  p6  Ss     0:00.33 -tcsh (tcsh)
  4300  p6  R+     0:00.01 ps

...note that immediately after "starting", the server's PID is not 
listed.  Here's the contents of error.log for this action:

- - - [24/March/2000:16:47:53 +0100] - - Low traffic settings.
- - - [24/March/2000:16:47:53 +0100] - - MiniMate is NOT active.
- - - [24/March/2000:16:47:53 +0100] - - MiniVend V4.02
- - - [24/March/2000:16:47:53 +0100] - - START server (4293) (INET and UNIX)
- - - [24/March/2000:16:47:54 +0100] - - Accepting connections from 
localhost|127\.0\.0\.1
- - - [24/March/2000:16:47:54 +0100] - - START server (4299) (INET and UNIX)
- - - [24/March/2000:16:47:54 +0100] - - INET mode server failed to start 
on port 7786: bind: Address already in use at 
/home/v/visprox/mvend/lib/Vend/Server.pm line 967.
 >
- - - [24/March/2000:16:47:54 +0100] - - INET mode server failed to start 
on port 7787: bind: Address already in use at 
/home/v/visprox/mvend/lib/Vend/Server.pm line 967.
 >
- - - [24/March/2000:16:47:54 +0100] - - INET mode server failed to start 
on port 7788: bind: Address already in use at 
/home/v/visprox/mvend/lib/Vend/Server.pm line 967.
 >
- - - [24/March/2000:16:47:54 +0100] - - INET mode server failed to start 
on port 7789: bind: Address already in use at 
/home/v/visprox/mvend/lib/Vend/Server.pm line 967.
 >
- - - [24/March/2000:16:47:54 +0100] - - Continuing in UNIX MODE ONLY

I don't know if this problem is caused because I tried to manually rename 
minivend.cfg.dist and start the server, or some other problem(s)...

You were right that deleting mvend/etc/minivend.pid allowed me to issue 
server commands, but as soon as it appears I get 'Could not lock file: 
Permission Denied' again.  If I delete it and issue the stop command, I get:

The Minivend server was not running (/home/v/visprox/mvend/etc/minivend.pid).

I am kind of lost here.  Any further suggestions you may have would be 
appreciated.

- Ed L.



>Also,  it should be fine if you only start in UNIX mode and the INET
>tests fail You only need one these methods to run your shop. UNIX is
>safer I believe, so ISPs prefer it. . It looks like it's the
>server/control test that's getting you. That happened to me when 4.x was
>in the alpha stage, and it turned out to be an issue with my BSD machine
>and the 'make test' script I think. I'm guessing the file that's locked is
>/home/v/visprox/mvend/etc/minivend.pid
>
>see if it exists and try deleting it to start the server again....
>
>Good luck!
>
>    -mark
>
>   <<-------------------------------------------------------------->>
>personal website                <    Summersault Website Design
>    http://mark.stosberg.com/     >       http://www.summersault.com/
>-
>To unsubscribe from the list, DO NOT REPLY to this message.  Instead, send
>email with 'UNSUBSCRIBE minivend-users' in the body to Majordomo@minivend.com.
>Archive of past messages: http://www.minivend.com/minivend/minivend-list

-
To unsubscribe from the list, DO NOT REPLY to this message.  Instead, send
email with 'UNSUBSCRIBE minivend-users' in the body to Majordomo@minivend.com.
Archive of past messages: http://www.minivend.com/minivend/minivend-list


Search for: Match: Format: Sort by: